Color: Silver A2017 and A5052 materials used Silver anodized finish
*Images are for reference only.Other colorings / other types may be included.
●Honda Horizontal Engine ●Compatible models and head shapes: Monkey 6V / 12V, Dax 6V / 12V, Monkey R, Kitakoutra SE, Regular head of each company ●This is a new oil cooler that can be installed directly to the head.Installation is very easy, just remove the stock cover and install.There is no need to worry about troublesome hose routing, modification of the bracket, or interference with the bike body.Since oil is circulated inside, a high cooling effect can be obtained.Not for use with Chaly.(It will interfere with the frame.)
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Recently viewed products
Ratings & reviews for this product or related products
When it comes to G-Craft products this is built well.looks great and works as it should. Also gives a custom appeal. It was fitted on my yx 140cc engine View Detail
ENG : good oil cooler for small engine 1st i use parts before i must check inside the engine, run after 1000km open the engine head. so keep watching for my next review. thanks KOR : 시티에이스 / 시티100 에 호환 가능합니다 의문점이 한가지 있는게 한국 시티류 엔진은 오일펌프를 통해서 헤드 속에 벨브에게 위에서 부터 오일이 뿜어져 나옴으로써 오일이 아래로 흘려내려가는 구조가 되게끔 되어있으나 이것은 혼다 소형엔진들을 위한것인지 오일라인이 아래쪽으로 되어있어서 헤드 아래쪽에만 오일이 흐르는것인지 궁금합니다 그래서 장착 후 1000km 이 지나고 나면 열어서 확인해 볼 생각입니다 냉각자체에는 상당한 도움이 됬습니다View Detail
ENG: fit to 110~125cc horizontal engine ( old cub,monkey,etc) easy to install, Ignition cap almost touched billet i dont mind that :-)KOR: 시티엔진에 100% 호환가능합니다만 설치에 주의할점이 있습니다 엔진헤드 원형카바 (사진의 반대편에 원형파츠) 와 연결되는 긴 볼트는 가장 나중에 조립하시고 작은 볼트 2개 (빌렛의 위 아래) 에 한번에 하나씩 조립하지마시고 위아래 조금씩 돌려가며 수직을 맞춰가며 조립해야합니다 볼트와 빌렛에 간섭이 있습니다 분해할때도 마찬가지로 한번에 볼트를 다 풀어버리면 핀이 휘어버립니다 조심해야합니다... 표면이 날카롭습니다 CNC 가공한것 같은데.. 후처리가 안되있어서 장갑을 착용하세요JPN: 独特のエンジン熱を冷ます 表面が鋭いので手に気をつけてください。 WIND SHIELDのない水平エンジン互換可能 これからの様々なものを期待します。View Detail
Even if you see the imprints in various places, plug attachment / detachability, interference between Plug cap and Body etc.. To I do not see anything that I mentioned deeply, so I will upload what I tried by myself and tried it.
The first image was originally attached Plug cap, NGK LD 05 F. Even after inserting in a degree that it is hard to fit slightly, it does not make contact with the cooler Body and there is no problem. Some of them seem to have cut Plug cap and others, This was no problem.
The second image is a state in which the product specified KTC's Plug wrench, B12P - 16H is inserted. It is quite rich Clearance at Limit to insert, but this also has no problem. However, as soon as you relaxed it was necessary to immediately withdraw Wrench and then turn it by hand to remove it. When tightening the plug, it is useless unless you go through the reverse procedure. 12mm Spanner turning Wrench may also be bad or thick.
For reference, the image engine is equipped with JUN's BFHead, and it is wearing it. It seems that it does not cause catastrophic interference around the Plug even in 10 steps.View Detail
I watched Impre, I bought it as a reference for the time being. I do not know whether it's good or bad but I installed it and saw it. Installation is easy.
I do not know if the effect is effective or not effective.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!